Product Categories
Contact Us

Chongqing Bishan Jiecheng Plastic Co., Ltd.

Add:Shiyang 3rd Road, Qinggang Street,Bishan District,Chongqing,China

E-mail:sales@cqjiecheng.com

Office:+86-23-41802788

Fax:+86-23-41801788


News

Laminating Machine Self - Defense Of The Security Ideology

What is the principle of automatic correction device for compound machine? Which sensors (ultrasonic, photoelectric, pneumatic, etc.) are commonly used? What is the difference between these sensors?

The automatic correction device is a system that automatically detects and controls the lateral position of the tape. It is through the sensor to detect the edge or edge of the tape (substrate), the use of the control system to calculate the analysis of its lateral position of the fluctuations or errors, and issued an error correction instructions by the implementing agencies to correct the horizontal position of the tape.

Commonly used sensors are ultrasonic sensors, photoelectric sensors and pneumatic sensors. Ultrasonic sensors are available for all materials and are generally used for heel. Photoelectric sensors are mainly used for the line, but can not be used in the transparent substrate with the edge. Pneumatic sensors are suitable for all materials with the edge, but the general accuracy is low.

First, the purpose: 

Standardize the operation procedures and methods of complex machine to ensure personal safety, equipment safety and product quality and stability. The following are the same as the 

Second, the scope of application:

Applicable to complex machine operation and new employee training. The following are the same as the 

Third, the composite process Overview:

Composite process refers to: the printing substrate (coated paper) and printing substrate (laser aluminum) by the glue tank into the adhesive (water-based adhesive) tightly together, with the guide roller and torque control So that the success of the winding way. The following are the same as the 

Fourth, the complex operation steps:

(A) do a good job before the boot check and security work

1, before the boot check the machine surface no work-related items, chain, guide roller without foreign body, check the bare machine outside the wire without damage, check the electrical device is normal, whether in a state of control, found abnormal, timely processing.

The following are the same as the 

2, in order to ensure the quality of composite products, boot must be strictly checked before the complex machine on the guide roller hygiene, witness the light guide and flexible rotation of the case, before the boot operation.

The following are the same as theWhat is the principle of automatic correction device for compound machine? Which sensors (ultrasonic, photoelectric, pneumatic, etc.) are commonly used? What is the difference between these sensors?

The automatic correction device is a system that automatically detects and controls the lateral position of the tape. It is through the sensor to detect the edge or edge of the tape (substrate), the use of the control system to calculate the analysis of its lateral position of the fluctuations or errors, and issued an error correction instructions by the implementing agencies to correct the horizontal position of the tape.

Commonly used sensors are ultrasonic sensors, photoelectric sensors and pneumatic sensors. Ultrasonic sensors are available for all materials and are generally used for heel. Photoelectric sensors are mainly used for the line, but can not be used in the transparent substrate with the edge. Pneumatic sensors are suitable for all materials with the edge, but the general accuracy is low.

First, the purpose: 

Standardize the operation procedures and methods of complex machine to ensure personal safety, equipment safety and product quality and stability. The following are the same as the 

Second, the scope of application:

Applicable to complex machine operation and new employee training. The following are the same as the 

Third, the composite process Overview:

Composite process refers to: the printing substrate (coated paper) and printing substrate (laser aluminum) by the glue tank into the adhesive (water-based adhesive) tightly together, with the guide roller and torque control So that the success of the winding way. The following are the same as the

Fourth, the complex operation steps:

(A) do a good job before the boot check and security work

1, before the boot check the machine surface no work-related items, chain, guide roller without foreign body, check the bare machine outside the wire without damage, check the electrical device is normal, whether in a state of control, found abnormal, timely processing.

The following are the same as the 

2, in order to ensure the quality of composite products, boot must be strictly checked before the complex machine on the guide roller hygiene, witness the light guide and flexible rotation of the case, before the boot operation.

The following are the same as the

Before the boot operation to strengthen self-defense of the security ideology, wear the necessary labor insurance products, such as uniforms, gloves and so on. The following are the same as the 

(B) boot

1, open the torque motor controller of the main switch, push thepressure roller button, the pressure roller rise. The following are the same as the 

2, according to the company's production plan to choose a suitable width and quantitative paper roll (Note: width unit: mm, such as: 340mm, 370mm, 380mm, etc .; quantitative units: g / m2, such as: 58g / m2, 64g / m2, / M2, etc.), the gas shaft into the paper roll has been selected into the paper roll, roll the paper roller to the installation location to install, click the lift device to roll the paper from the ground to the appropriate location.

The following are the same as the 

3, the paper roller to adjust the position, so that the right edge of the "electronic eye" to install the paper roll gas up the shaft filled with gas, according to the specified direction of the machine to pull the paper through the paper guide roll roll roll. The following are the same as the "

4, from the rewinding of the composite machine will be the beginning of the beginning of the tape in the opposite direction of the composite work through the guide roller to the glue tank and the bottom of the film roll, the paper and paper roller traction end bonding.

5, the temporary coordination of mobile personnel or other positions to assist the complex owner of the operator to do the auxiliary work (such as: composite work of the boot, shutdown, for film roll, paper roller, winding unloading operation). The following are the same as the 

6, according to the company's production plan to choose the appropriate specifications (Note: specifications that the width of the film, such as: 340mm, 370mm, 380mm, etc.) and style (style that is laser shape, such as: big peach, large grid, gear, Point, sand column light beam, flat beam, pull scarves, etc.) of the laser film, the gas shaft into the selected laser film core, with electric hoist hanging to the installation of the machine roll stand. And by the main operation of the complex machine in the laser film into the library account to do a good job on the library records. The following are the same as the

7, the glue tank installed in the roller and steel roller below, check the glue tank glue switch is closed (Note: should be closed, to prevent injection when the drip). The following are the same as the

8, take a bucket of water-based composite plastic cover, with a hose to glue evenly, the hose hose into the plastic tank into a certain amount of water-based adhesive (Note: glue into the glue to be just right, not Excessive, to prevent running). The following are the same as the

9, plastic tank after injection, manually turn the rubber roller, adjust the pressure between the rubber roller and steel roller, the rubber roller and steel roller coated with a thin and uniform water-based composite adhesive.

The following are the same as the

To the winding part of the composite machine, according to the direction of the composite work pull the paper, so that the paper and the paper roller pull the end of the adhesive at the west side of the plastic tank; to the gas up shaft mounted on the precise positioning of the core, The end of the tape with tape and paper core adhesion, and gas up the shaft filled with gas, pressure on the west side of the pressure roller.

The following are the same as the

The membrane roller to adjust the position, so that the right edge of the electronic eye to the installation of the membrane roll gas up the shaft filled with gas, traction laser film through the film guide roll roll, close to the top of the roller through the pressure Roller, so that the film and paper bonding, compaction of the east side of the pressure roller.

The following are the same as the

12, by the composite machine operators, respectively, the paper roller photoelectric correction controller, magnetic brake and laser film roller photoelectric correction controller point to the automatic state.

The following are the same as the

13, the main operation of the complex machine issued a boot password, mobile personnel or other staff to the moment before the motor controller, respectively, according to the host start and winding start button, then slowly fine-tuning torque motor controller tension knob And the speed knob {Note: the torque motor controller when the tension knob from 0 to 60 in the middle of the fine position, and then synchronized with the speed control knob 300 (r / min), then the torque motor controller tension knob final Adjusted to 150-151 position; then the speed control knob from 300 (r / min) slowly fine to 600 (r / min)}.

The following are the same as th

14, the normal operation of complex operations, mobile personnel or other staff back to the original post work. The following are the same as the

(3) process control

1, after the switch machine running, the main operator depending on the operation of the complex machine, according to the paper roll, membrane roll volume changes, etc., reasonable adjustment of paper roll tension, film roll tension and composite pressure. The following are the same as the "

2, the complex machine running process, by the main operation of the complex machine as the size of the change, the torque motor controller speed control knob slowly transferred to 1200 (r / min), the complex into the high-speed operation. The following are the same as the "

The main operator of the composite machine shall not leave the job in the course of the composite operation, and shall be directly responsible for the product quality control of the composite operation process.

4, composite operation process found in the composite film wrinkles should be immediately according to the actual situation to determine the main cause of wrinkles, check it from the paper or from the film, and then immediately make a reasonable adjustment.

Before the boot operation to strengthen self-defense of the security ideology, wear the necessary labor insurance products, such as uniforms, gloves and so on. The following are the same as the "

(B) boot

1, open the torque motor controller of the main switch, push the "pressure roller" button, the pressure roller rise. The following are the same as the

2, according to the company's production plan to choose a suitable width and quantitative paper roll (Note: width unit: mm, such as: 340mm, 370mm, 380mm, etc .; quantitative units: g / m2, such as: 58g / m2, 64g / m2, / M2, etc.), the gas shaft into the paper roll has been selected into the paper roll, roll the paper roller to the installation location to install, click the lift device to roll the paper from the ground to the appropriate location.

The following are the same as the

3, the paper roller to adjust the position, so that the right edge of the "electronic eye" to install the paper roll gas up the shaft filled with gas, according to the specified direction of the machine to pull the paper through the paper guide roll roll roll. The following are the same as the

4, from the rewinding of the composite machine will be the beginning of the beginning of the tape in the opposite direction of the composite work through the guide roller to the glue tank and the bottom of the film roll, the paper and paper roller traction end bonding.

5, the temporary coordination of mobile personnel or other positions to assist the complex owner of the operator to do the auxiliary work (such as: composite work of the boot, shutdown, for film roll, paper roller, winding unloading operation). The following are the same as the

6, according to the company's production plan to choose the appropriate specifications (Note: specifications that the width of the film, such as: 340mm, 370mm, 380mm, etc.) and style (style that is laser shape, such as: big peach, large grid, gear, Point, sand column light beam, flat beam, pull scarves, etc.) of the laser film, the gas shaft into the selected laser film core, with electric hoist hanging to the installation of the machine roll stand. And by the main operation of the complex machine in the "laser film into the library account" to do a good job on the library records. The following are the same as the

7, the glue tank installed in the roller and steel roller below, check the glue tank glue switch is closed (Note: should be closed, to prevent injection when the drip). The following are the same as the

8, take a bucket of water-based composite plastic cover, with a hose to glue evenly, the hose hose into the plastic tank into a certain amount of water-based adhesive (Note: glue into the glue to be just right, not Excessive, to prevent running). The following are the same as the

9, plastic tank after injection, manually turn the rubber roller, adjust the pressure between the rubber roller and steel roller, the rubber roller and steel roller coated with a thin and uniform water-based composite adhesive.

The following are the same as the

To the winding part of the composite machine, according to the direction of the composite work pull the paper, so that the paper and the paper roller pull the end of the adhesive at the west side of the plastic tank; to the gas up shaft mounted on the precise positioning of the core, The end of the tape with tape and paper core adhesion, and gas up the shaft filled with gas, pressure on the west side of the pressure roller.